Bluetooth 연결
Bluetooth 무선 기술로 다른 장치에 컨트롤러를 연결하기 위한 단계가 아래에 설명됩니다.
Bluetooth를 지원하는 장치면 다음 어떤 것에든 컨트롤러를 연결할 수 있습니다.
- Trimble GNSS 수신기
- Trimble 광파 측량기
- Trimble Data Link Radio (TDL) 2.4 GHz 라디오 장치
- Trimble 활성 타겟
- 보조 GPS 수신기
- 레이저 거리계
- 음향측심기
- 다른 컨트롤러
- 외장 라디오 장치
컨트롤러를 휴대폰이나 외부 모뎀에 연결하고 그 연결 장치를 사용해 인터넷에 연결할 수도 있습니다. 이러한 연결 생성에 대해서는 인터넷 연결 설정을 참조하십시오.
컨트롤러가 인근의 Bluetooth 장치를 검색할 때 해당 장치를 찾을 수 있게 하려면 장치에서 Bluetooth를 활성화하고 검색 가능 설정을 활성화하도록 합니다. 자세한 정보는 사용 장치의 설명서를 참고하십시오.
다음 장치를 사용할 때:
- Trimble 활성 타겟을 사용하면 활성 타겟이 켜져 있을 때 항상 Bluetooth이 활성화됩니다.
- Trimble Data Link Radio (TDL) 2.4 GHz 라디오 장치를 사용하면 2초간 라디오 버튼을 눌러 이것을 검색 가능한 상태로 만듭니다. 파란색과 빨간색 LED가 깜박여 라디오가 페어링 준비가 되었음을 나타냅니다. 10초 이상 라디오 버튼을 계속 누르면 TDL2.4에서 모든 저장 Bluetooth 페어링이 지워집니다. TDL2.4와 컨트롤러 간 Bluetooth 페어링을 다시 만들어야 할 것입니다.
Bluetooth가 Trimble Access 외부의 액션으로 해제될 경우 소프트웨어에 의해 Bluetooth가 켜지게 하려면:
- 늘 누르고 설정 / 연결 / Bluetooth를 선택합니다.
- Bluetooth 자동 활성화를 선택합니다.
수동으로 Bluetooth를 활성화하려면 시스템 트레이의 화살표를 누릅니다. Bluetooth 아이콘이 비활성 상태면 Bluetooth 아이콘을 누른 뒤 Bluetooth 활성화 옵션을 선택합니다.
어떤 컨트롤러를 다른 컨트롤러에 연결하려면 양쪽 컨트롤러에서 Bluetooth를 활성화해야 합니다.
어떤 컨트롤러를 다른 컨트롤러에 연결하려면 한쪽 컨트롤러에서 다음 단계를 수행하도록 합니다.
- 스캐닝을 할 때 정확한 컨트롤러를 찾아내는 것을 용이하게 하려면 이 컨트롤러에 고유한 이름을 부여하도록 합니다. 운영 체제의 컴퓨터 이름이나 장치 이름 설정으로써 컨트롤러의 이름을 바꾸면 됩니다.
- 늘 누르고 설정 / 연결 / Bluetooth를 선택합니다.로 가십시오.
-
설정을 누릅니다. Bluetooth 장치 화면이 나오고 컨트롤러가 자동으로 장치를 검색합니다.
연결하고자 하는 장치가 자동으로 나타나지 않거나 자동으로 스캔이 시작되지 않으면 장치 추가 옵션을 선택합니다.
장치는 이미 Bluetooth 무선 송수신 장치가 사용 중이라면 스캔에 반응을 하지 않습니다.
내장 모뎀이 있는 Trimble GNSS 수신기와 컨트롤러를 페어링 한다면 수신기와 별개로 모뎀을 따로 검색할 필요가 없습니다. Trimble GNSS 수신기와 내장 모뎀은 Bluetooth 스캔에서 동일한 장치(그러나 시리얼 포트와 전화접속 네트워킹 기능이 있는)로 인식됩니다.
- 일단 스캔이 완료되면 연결할 Bluetooth 장치를 선택하고 화면상의 지시에 따릅니다.
-
PIN이나 패스키를 입력합니다. 기본 패스키:
- Trimble GNSS 수신기는 0000. 수신기 설정을 구성하기 위해 수신기 웹 인터페이스에서 이것을 바꿀 수 있습니다.
- Trimble LaserAce 1000이나 MDL LaserAce 레이저 거리계는 1234
- Ohmex SonarMite 음향측심기는 1111
그 밖의 장치에 대한 패스키는 장치 설명서를 참조하십시오.
- 지시에 따라 다른 장치에 동일한 패스키를 입력합니다.
-
확인을 누릅니다.
이제 장치가 컨트롤러에서 신뢰할 수 있는 장치의 목록에 나옵니다. 셀 모뎀과 페어링을 한 경우에는 이제 컨트롤러가 셀 모뎀에서 페어링 장치로 나옵니다.
페어링된 기타 다른 장치의 경우:
- 늘 누르고 설정 / 연결 / Bluetooth를 선택합니다.
-
해당되는 입력란에서 연결 대상 장치를 선택하고 수용을 누릅니다.
자동 연결 기능이 활성화되어 있으면 Trimble Access 소프트웨어가 몇 초 이내에 해당 장치에 연결됩니다. 그렇지 않으면 측량을 시작해 장치에 연결합니다.
TDL2.4을 Trimble VX Spatial Station 또는 Trimble S Series 토탈 스테이션에 연결하려면 TDL2.4을 구성해 측량기와 동일한 라디오 설정을 사용해야 합니다.
- 수용을 누릅니다.
Bluetooth 화면의 장치 입력란에서 설정을 변경하지 않은 한, 컨트롤러는 양쪽 장치를 다 켜는 다음 번에 선택된 장치와 자동 연결됩니다.
Trimble GNSS 수신기에 다시 연결하려고 할 때 Bluetooth 오류 10051이 나오면 수신기의 GNSS 펌웨어가 업데이트되었고 설정이 기본값으로 초기화되었습니다. Trimble Access 소프트웨어에서 페어링을 삭제한 뒤 다시 페어링을 해야 합니다.