Stylesheets

12D field file report

The 12d field format file stylesheet produces an output file in the 12d Model FLD format to allow the field data to be imported directly into a 12d Model project.

Area computation report

The Area computation report stylesheet produces a report on all the area computations, including subdivided areas.

Averaged points report

The Averaged points report stylesheet produces a report on all the averaged points in the job providing the averaged position along with the computed standard errors.

Bouyges report

This stylesheet creates an output format for total station data, well structured and in French language.

CAPLAN Z-format

Files created by this stylesheet can be imported directly into the CAPLAN office software.

Carlson RW5 file

Creates an output file in the Carlson RW5 file format.

Check shot report

Reports delta values for check shots observed with conventional and GNSS instruments.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

CMM coordinates

Outputs the northing and easting values for points in the CMM oordinates format.

CMM elevations

Outputs the elevation values for points in the CMM elevations format.

Combined stakeout report

This stylesheet provides a combined report of all the staked points in a job. The points can be reported in observed order or by stakeout type and a date range can be specified for the output points. Extra output sorting has been added when the Grouped by stakeout type option is used.

Comma delimited with depth applied

This stylesheet is designed for use with data collected using echo sounder support. It produces a CSV file that has the echo sounder depth value applied to the elevation. There is an option to allow only the output of points with echo sounder depths.

Comma delimited with elevation and depths

This stylesheet is designed for use with data collected using an echo sounder. It produces a CSV file that provides both the elevation and the depth values for points. There is an option to allow only the output of points with echo sounder depths.

Comma delimited with HA, VA, SD, time, date

Creates a CSV file from the observation data in the job and includes the point name, point coordinates, observed horizontal angle, observed vertical angle, slope distance, time, date and point code.

Comma delimited with multiple stake elevations

This stylesheet will report the details for extra stake elevations that have been staked as part of a stakeout operation using a stakeout stylesheet that requests extra design elevations, for example the Point - Stake multiple elevs point staked deltas format.

Comma delimited with notes

Creates a CSV file of the points in the job and for each point will include any notes that have been assigned to the point. Any notes entered immediately following a point will also be included with the point. In addition there is an option to output any attributes assigned to points (output in the same manner as for the Comma delimited with attributes stylesheet). Any point descriptions are also included. The notes output follows all the other output details.

Computed station and offset values

Use this stylesheet to compute the station and offset values for the points in the job based on the specified RXL road definition. The stylesheet will load the RXL file for the specified road and then use the horizontal alignment definition to compute the station and offset for each point that can be projected onto the alignment. The data is output as a CSV file.

Cross slope details report

This stylesheet will report the cross slope vertical deltas determined during road staking operations. The column headings for the report are: Chainage, Offset, Hz Const Offset, Vt Const Offset, Cut/Fill, Cross slope Vt Delta.

CSV Global Lat-Long points

Creates a CSV file of the points in the job with Global Latitude and Longitude and height, code and descriptions.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

CSV with attributes

Creates a CSV file of the points in the job and includes the point code plus any features and attributes assigned to the points as well as the point name and coordinates. Each attribute value included with a point is preceded by the attribute name (prefixed with the feature name and a colon). If the points have any descriptions assigned to them these will follow the attributes.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Cut sheet 1 (road stakeout reporting only)

Column headings - Station, Offset, Description, Construction Offset, Design Elevation, True Elevation, Cut/Fill.

Cut sheet 2 (road, alignment, Line and arc stakeout reporting only)

Column headings - STA, O/S, EL, GRADE, CUT, FILL, DESC.

Cut sheet 3

Column headings - Point, Code, North, East, Elev, Design Elev, Cut/Fill.

Diameter from 3 points

This stylesheet will compute the diameter of circles formed by groups of 3 points in 3D space. The points to be used in the computations must be assigned a specific code, and code to be used for the point selection is prompted for when the stylesheet is run. The stylesheet works by finding the first 3 points (in the order encountered in the job) with their code matching the specified code, and uses these points to compute the diameter. The stylesheet continues searching for sets of 3 points with matching codes until there are no more matching points, computing the diameter and circumference for each set of 3 points.

DTM check report (Denmark)

This stylesheet is designed for use in Denmark and reports the vertical deltas for staked road points to either the design DTM or the road design.

DTM deltas report (Denmark)

This stylesheet is designed for use in Denmark and reports road design staking details with the vertical deltas for both the design DTM and the road design.

DTM stakeout report

This stylesheet reports the vertical deltas (cut/fill) for staked DTM points. The column headings are: Name, Vert offset, Cut/Fill, Code.

DXF file (AutoCAD 2000)

The DXF file stylesheet will create an AutoCAD 2000 version DXF file containing the points from the job. The stylesheet allows you to choose from a set of simple block definitions to be used for the points. It also provides an option to split the data into layers based on the point codes. The stylesheet will also carry out some simple feature code processing as it creates the DXF file to join up points based on their codes. The point names and features codes for points are assigned as attributes to the point blocks inserted for the points.

ETRS89 Einzel+Mittel (Germany)

This stylesheet is designed to create a report on RTK points specifically for the German market. The points are reported as global ECEF X,Y,Z values. There is an option to output all the individual positions for points or only the averaged positions for points measured multiple times.

ETRS89 Messdatei details (Germany)

This stylesheet is designed to create a report on RTK measurement details specifically for the German market. It reports the point names with their antenna heights, time of measurement and quality values.

ExportuFormat

This is a data format specifically designed for the Romanian market.

FBK file

This stylesheet will output Autodesk FBK format files suitable for use in AutoCAD Civil 3D and Autodesk Land Desktop systems. The stylesheet will expand abbreviated figure commands ('B ' for 'BEGIN ' etc) and will insert appropriate END and CONT (continue) commands for figure joining.

France stakeout format

This is a CSV format, but it contains stakeout information (Design Point Name, Design Point Easting, Design Point Northing, Design Point Elevation, Staked Easting, Staked Northing, Staked Elevation, Delta Easting, Delta Northing, Delta Elevation).

FSP format

This stylesheet will output a file suitable for use in the Field Survey Processor system.

GAZEAU format

This is a standard CSV file (Name, Easting, Northing, Elevation, Code), but it has a header line containing some job details.

GDM area

This stylesheet outputs the coordinates of the points from the job in the Geodimeter area file format.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

GDM job

This stylesheet outputs the conventional observations from the job in the Geodimeter job file format.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

GDM job with descriptions

A Geodimeter Job format which adds the text of the two additional description fields to the code (label 4).

GDM format with 2 descriptions

In addition to Hz, V, El and coordinates this format also contains the information of the two optional description fields.

Geocomp format

This stylesheet will output a file suitable for use in the Geocomp system.

GNSS Vector Exchange

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

GPS points report (text)

This stylesheet creates a text file report of the points in the job that provides the point name, grid coordinates, point code, horizontal and vertical precisions, PDOP and number of satellites. There is an option to sort the points either numerically or alphabetically.

GPS calibration report

This GPS calibration report stylesheet reports the details of the GPS calibration in a job.

GPS-averages format

This stylesheet writes out coordinates and statistical data for RTK observations and calculates averages for points which were observed more than one time (store another).

GPX point export

Exports GNSS positions into the standard GPX data exchange format.

Grid (local) coordinates

This stylesheet is designed to provide both the grid and grid (local) coordinates as comma separated values for jobs where a local transformation has been defined. The stylesheet provides a user option to choose the output of either Computed local grid coordinates or Entered local grid coordinates.

GT format (Finland)

This stylesheet outputs the points from the job in the GT format used in Finland.

Instrument collimation report

This report presents the instrument collimation details that have been recorded in the job file. It will present each unique set of collimation details so that, if the instrument collimation has been adjusted during the course of the job, the collimation details before and after the adjustment will be reported. Similarly, if different instruments have been used in a job then the collimation details for each instrument will be reported.

Intrasis 3 codes

This stylesheet adds the text of the two additional description fields to the code field of the Intrasis format.

Intrasis raw format

This is a modified GDM format. The file starts with job name, date, time, operator, description, 3D standard deviation of the resection, note and reference. After this information it continues with the standard values, Name, Code, Northing, Easting, Elevation.

ISO rounds report

Reports the observations and residuals from rounds observations in an ISO standard report format. Stylesheets for creating an HTML report and a Microsoft Word XML report (for opening directly in Microsoft Word) are provided.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Izvestaj GPS merenja (Serbia)

This is an HTML report on GNSS observation data in Serbian language.

Izvestaj merenja totalnom stanicom (Serbia)

This is an HTML report on total station data in Serbian language.

Job costing report

This Job costing report stylesheet provides occupation time details using the time stamp data recorded in a job to assist in cost estimation for survey work.

Karlsruhe observation with code

A format that adds code information to the Karlsruhe observation format.

Karlsruhe observations format

This stylesheet creates a file containing total station raw data. Station records: Standpunkt, name, instrument height; Observation records: Zielpunkt, name, target height, Hz, V, D.

KAVDI format

Files created by this stylesheet can be imported directly into the KAVDI office software.

KOF file (Norway)

Creates a standard KOF format file for use in Norway. There is a second stylesheet that only writes out first space separated code.

KML file

This stylesheet will create a KML file that can be used to view the GPS points from a job in Google Earth.

LandXML to pipe alignment LandXML

The LandXML to pipe alignment LandXML stylesheet takes a Pipe Network LandXML file with Pipe, Structure and Horizontal Alignment records and creates vertical geometry from the structure records to go with the original horizontal alignment to enable staking of pipes and manholes from the alignments. For more information, watch the video Staking Pipe Structures from LandXML Files.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

LandXML format

This stylesheet will output a generalised LandXML format file containing all the points and keyed in lines and arcs from the job. Any features and attributes assigned to a point are included in a Feature element following the point's CgPoint element, with the Feature source attribute referencing the point name.

Lantmäteriverket (Sweden)

This stylesheet outputs the points from the job in the standard Lantmäteriverket format used in Sweden.

LINZ LandXML format

This stylesheet will create a LandXML file suitable for use in applications that deal with Land Information New Zealand (LINZ) LandXML format file, referencing the LandXML V1.2 schema.

LisCAD field file export (2023)

This stylesheet will create a LISCAD field file formatted for direct import into the LISCAD office software. The stylesheet carries out special processing to structure the data to work with the LISCAD coding system. Has optional output of GNSS QC data to the new LisCAD 510 record.

Local grid coordinates

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Local transformations report

This stylesheet provides a report with the transformation details for each local transformation defined in the job.

LSS Load file

This stylesheet creates a LSS 'Load file'. The Load file format is the principle survey import file format for the LSS software from McCarthy Taylor Systems Ltd. LSS load files can be directly loaded into LSS. All EDM data is output as radials (including all set-up information) and GPS data is output as point coordinates. The codes are output in LSS format, and the reserved code attributes (via the LSS export FXL code library option) are automatically reformatted. The Quality values for GPS records are output when outside tolerances.

McCarthy Taylor Systems Ltd are an independent UK based software house specialising in 3D terrain modelling software. Stylesheet courtesy of Trimble dealer Survey Solutions Scotland and McCarthy Taylors LSS.

Media file report

This stylesheet will report the names of all the image files referenced in a job, along with the points they are associated with and the date and time they were recorded. If an image has not been assigned to a point then the job file name is reported.

Monitoring points report

This is an HTML report on deformation measurements made from different stations and it shows the deltas to the reference coordinates as well as to the previous measurement.

Monitoring report

This stylesheet can be used to present the results of a monitoring observations made as a series of rounds of observations. It reports the deltas between the observations.

MOSS input (Survey option) format

Creates a MOSS (MX Road) survey format file containing the conventional observations from the job so that they can be imported into a MOSS (MX Road) system.

MX topo GENIO format

Creates a MOSS (MX Road) GENIO format file. The stylesheet will group all the point code points (codes starting with 'P') together into point strings. It uses the observation sequence to string the other points together, automatically starting a new string when the code changes. A new string control code can also be specified and a feature code with this control code added at the end (separated with a space) will also force the start of a new string.

Nikon raw format

Creates a Nikon raw format file containing the conventional observations from the job.

NZ Fieldbook report (Word)

This stylesheet will produce a report of GPS and conventional measurements in a form suitable for use in New Zealand cadastral surveys. The report is produced in a Microsoft Word XML format that can be opened directly in Microsoft Word 2003 or later. This will simplify the creation of printed reports.

NZ Fieldbook report

This stylesheet will produce a standardised report to comply with the Field Information submission requirements for Landonline Cadastral Survey Datasets (CSDs) detailed in the Cadastral Survey Rules 2021 (CRS 2021). The report, includes project, job and coordinate system settings, GNSS and conventional survey measurements, coordinate tables, and photographs. The report produced from this stylesheet can be either in an HTML format, or when generated on a controller a PDF format.

ODB output

Files created by this stylesheet can be imported directly into the ODB office software.

Output grid for each observation

This stylesheet will output a comma separated list of the grid coordinates for each observed point in the job. This means that if a point has been measured multiple times (for example, in a set of rounds) then the grid coordinates for each individual observation will be output.

Point comparison report

This stylesheet compares each point in a job with all the other points, and then reports the pairs of points that are within the user specified horizontal and vertical tolerances. As this stylesheet needs to carry out a lot of processing it can be slow on some data collectors. For faster processing, use the stylesheet with the File and Report Generator utility or the Job Report Generator in your Trimble office software.

Point stakeout cut sheet

Column headings - Name, Code, Design N, Design E, Design Z, As Staked N, As Staked E, As Staked Z, Cut/Fill, Δ N, Δ E, Δ Z.

Points and notes report

This stylesheet is designed to list all the point names in the job, in the order in which they were observed, along with their point code and any notes assigned to points, or included in the job along with the points. This can be a useful report to supply to a CAD operator to assist them in understanding how the surveyed points are to be handled in the CAD system.

Points on plane report

This stylesheet reports the details of the plane definitions for all planes defined in the job that have points measured with respect to them, and reports all the measured points, including the perpendicular deltas for measured rather than intersected points.

Pregeo 2021 RTX

Updated Pregeo (Italy) for RTX.

Pregeo format (Italy)

This stylesheet exports the point data from the job in the standard Pregeo format used in Italy.

Pregeo NRTK (Italy)

This version of the Pregeo stylesheet allows the export of vectors from VRS positions.

Productivity report

This stylesheet provides details of the occupation times of different base and instrument setups, along with counts of the number of points observed or staked in each setup.

Prüfpunktbericht

This is the translated German version of the 'Check shot report' stylesheet.

PWGS84 format

This stylesheet outputs WGS84 coordinates for GNSS observations, but it lets you choose whether you want to have it in ECEF, decimal degrees or degree-minute-second format.

PXY format (Denmark)

This stylesheet exports the point data from the job in the PXY format used in Denmark.

Quality control report

This stylesheet creates a report on the job providing details of the instruments/receivers used, GPS base points used, antenna heights used, points with precisions and PDOP’s outside specified tolerances, GPS points without a fixed solution, lists of any points fixed prior to a loss of initialization due to high RMS within 5 minutes of initialization, instrument station setups used, target heights used, check observations taken and a list of duplicate points observed, with deltas from the mean position.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Rapport implantation combiné

This is a French language stakeout report.

Raw+Coords format

This stylesheet creates an ASCII file of conventional data reporting station, backsight and observation points.

Red heading elevations report

This stylesheet reports the staked elevations for staked road points. The column headings are: Station, Offset, Elevation.

rmData format

This stylesheet creates files in a format that can be imported into the rmData software.

Road, line, arc stakeout report

This is a generic cut sheet report for reporting points staked on roads, alignments, lines and arcs. There is an option provided to identify the reported points by name or by station and offset and an option to allow the delta elevations to a DTM to be reported. The column headings are: Name or Station/Offset, dStation, dOffset, dElev, (optional DTM), Code.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

SBG format (Sweden)

This stylesheet exports the point data from the job in SBG format (used in Sweden).

SDMS format

Creates a SDMS (Survey Data Management System) format file. The file will include observation details for conventionally observed points and coordinates for RTK points. It will include any attributes or descriptions assigned to points as long as the attribute and description names are 2 character names (the SDMS standard).

SDR33 coordinates

Creates a SDR33 format file containing the coordinated points from the job.

SDR33 observations

Creates a SDR33 format file containing the conventional observations from the job file. Any GPS RTK points in the job are output as grid positions.

SFN format (Netherlands)

This stylesheet exports the point data from the job in the standard SFN format used in the Netherlands.

SOSI format (Norway)

This stylesheet exports the point data from the job in the standard SOSI format used in Norway.

Stakeout report

Creates a generalized stakeout report providing details of the points staked in the job. Tolerances can be specified to allow highlighting of out of tolerance values.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Surface inspection report

The Surface inspection stylesheet creates a PDF surface inspection report that includes a summary of the surface inspection parameters, any screen captures of the surface inspection, and any inspection points stored with the surface inspection.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Survey report

This stylesheet creates an HTML report providing details on all the work carried out in a job. This provides a report that can be used to help analyze what has been done in the job.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

TDS RW5 file

Creates a TDS RW5 format file of the job data.

TOP format (France)

This stylesheet outputs total station data in the French TOP format.

TOP format with code

This stylesheet outputs the French TOP format with code information.

TopCal observations format

This stylesheet creates a total station raw data output: station, target, Hz, V, D, target height, instrument height.

Topoji

This stylesheet creates a CSV format for importing into a specific office software: Name:X=Northing,Y=Easting,Z=Elevation,C=Code.

Transmission line intersection points

This stylesheet will locate angles only observations and determine the previous 2 consecutive full measurement observations and treat them as defining the ends of a transmission line segment. It will then use the angles only observations to compute an intersection point along the transmission line segment (using the vertical angle to determine the elevation). The resultant computed points are written out as points in a CSV file (name, north, east, elevation, code).

Traverse adjustment report

This stylesheet reports the traverse adjustments applied in traverses computed in the job.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Traverse deltas report

This stylesheet reports the amount of correction applied to points in a traverse adjustment computed in the job. For each traverse point it compares the position prior to the adjustment with the adjusted position.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Traverse format StarNet

This stylesheet creates a file allowing the direct import of traverse data into the StarNet software.

Trimble Data Exchange Format

This stylesheet outputs all the observation data in the standard Trimble Data Exchange format. Data in this format can be imported into products such as the StarNet adjustment package.

TS-Aufnahme (Germany)

This stylesheet produces a well structured German total station data report.

Vertical conformance report

This stylesheet is designed for reporting the conformance of a road surface based on 'Position on road' observations made in the job. Upper and lower vertical tolerances for the surface can be specified and the report will indicate points that exceed these tolerances as well as providing conformance statistics.

Volume computation report

This stylesheet presents a report containing any volume computations carried out in the job.

Volume computation report with units

This stylesheet presents the same report as the Volume computation report stylesheet but it allows you to select the units you want the volume and area values reported in.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Zeiss M5 observations

Creates a Zeiss M5 format file containing observations.

Zeiss M5 coordinates

Creates a M5 format file containing the point coordinates.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Zeiss M5 elevations for DiNi

This stylesheet outputs the elevations of all points in a job file in M5 format, so that they can be imported into the Trimble DiNi.

Point – Stake markup

This staked deltas format stylesheet provides a simplified stakeout display that presents the vertical distance (cut/fill) to the design point. If applicable, the vertical distance to a DTM is displayed.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Point – Stake multiple elevations

This staked deltas format stylesheet provides a stakeout display that allows you to edit the point design elevation (the cut/fill value will be updated) and entry of up to two extra design elevations with associated vertical offsets and updated cut/fill values.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Point staking (position tolerance check)

This stakeout stylesheet for point staking reports the cut/fill value in a simplified format with a warning presented if the positional accuracy is not within the defined limit.

Line – Stake markup

This staked deltas format stylesheet provides a simplified stakeout display that presents the vertical distance (cut/fill) to the design position. The appropriate station and offset values are reported, based on the selected line stakeout method.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Arc – Stake markup

This staked deltas format stylesheet provides a simplified stakeout display that presents the vertical distance (cut/fill) to the design position. The appropriate station and offset values are reported, based on the selected arc stakeout method.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

DTM – Stake markup

This staked deltas format stylesheet provides a simplified stakeout display that presents the vertical distance (cut/fill) to the DTM being staked.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Stake DTM and design elevation

This DTM stakeout stylesheet includes the design elevation in the reported DTM details once a DTM point has been staked out.

Stake manhole inverts

When staking a manhole with multiple inverts from a pipe network LandXML file, this staked deltas format stylesheet provides a simplified stakeout display that uses the extra invert elevations in the LandXML pipe network file to compute their associated vertical offsets and updated cut/fill values on the Confirm staked deltas screen.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Stake faces data

This stakeout stylesheet reports staked deltas for catch point staking in a form to assist in writing up the details on the faces and edges of the stake. The line by line details for the stake are displayed.

Road - catch and offsets

This staked deltas format stylesheet provides details of all the standard road staked deltas plus a list of the horizontal and vertical distances to each of the cross‑section positions from the staked offset position. The reported horizontal and vertical distances include the applied horizontal and vertical construction offsets.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Road – Stake markup

This staked deltas format stylesheet provides a simplified stakeout display that presents the vertical distance (cut/fill) to the road design position. Appropriate station and offset values and cross‑section details (in the case of catch point staking) are reported, based on the road stakeout method.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Road – XS details

This staked deltas format stylesheet provides details all the standard road staked deltas details as well as a list of the cross‑section elements (left and right) that define the design cross‑section at the selected station.

The link below provides this stylesheet in English. This stylesheet is also installed to the controller in your chosen language when you select a language pack in the Language and Help Files group in the Install updates tab of the Trimble Installation Manager.

Road - delta elevation to shoulder

This stakeout stylesheet reports the delta elevation from the staked position to a cross-section point with the specified code on the same side of the cross-section. You can change the code of the point for the delta elevation report by editing the stylesheet file. See the notes included in the stylesheet file near the start.

Road surface conformance

This stakeout stylesheet for "position on road" staking, reports whether the cut/fill value for a point measured on the defined road surface meets the upper and lower tolerance values defined in the stylesheet. It issues a warning when the measured position is outside either of the tolerance values, or a confirmation when within the tolerances.

Pipelines – Alignment stakeout

This staked deltas format stylesheet provides details of all the standard alignment staked deltas plus the ahead and behind station values are reported for positions measured in the internal and external angles of non‑tangential intersection points in the alignment.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Pipelines – Points stakeout

This staked deltas format stylesheet provides details of all the standard point staked deltas plus the ahead and behind station values are reported for positions measured in the internal and external angles of non‑tangential intersection points in the alignment.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

RoadXML to DC file

This stylesheet converts an RXL file to a DC file containing the road definition data.

RoadXML report

This stylesheet creates a report using the data in the RXL file, that lists the stations along the road (both geometric and regular stations) with identifiers for the geometric points and design elevations for each station. The instantaneous radius, azimuth and grid coordinates are reported for each station. This report can be used to assist in the validation of road designs prior to staking out.

RoadXML offset points report

This stylesheet creates a report using the data in the RXL file and lists the stations along the road (both geometric and regular stations) with identifiers for the geometric points and design elevations for each station. In addition the report will display the computed offsets and elevations for the positions at the end of the nominated cross-section element, left and right of the alignment, where templates are being applied. This report can be used to assist in the validation of road designs prior to staking out.

RoadXML stakeout report

This stylesheet creates a report of all the design positions on each cross-section along the road, based on the horizontal alignment, vertical profile, superelevation and widening parameters and template definitions and assignments. You can use this report to validate the road design prior staking out.

Catch points cut sheet

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Cut sheet (station and offset deltas)

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

LandXML to RoadXML file

This stylesheet presents the dialogs allowing the selection of the alignment and cross-section surface to be used. See the instructions available in the zip file for more details. The stylesheet has been designed to stop the inclusion of centreline vertical construction elements unless the vertical delta between the cross-section and vertical design is greater than 0.001. It has also been designed to not output of any templates for stations beyond the end of the vertical alignment.

ViaNova LandXML to GENIO file

This stylesheet converts a ViaNova LandXML file containing horizontal alignments and vertical profiles defined as groups of 'string' definitions by the ViaNova system, to a GENIO file containing the same string definitions.

Tunnel profiles Word report

This stylesheet is designed to be used only with the File and Report Generator utility.

This stylesheet produces a Microsoft Word XML format file (with a .doc file extension) that can be viewed in Microsoft Word. The Word file contains an initial cover page followed by a page per profile with a plot of the profile as well as a table of the points scanned on the profile.

When you apply the stylesheet using the File and Report Generator utility, you can select the TunnelXML file that defines the tunnel alignment and design profiles used during the tunnel scanning operation. The design profile will be displayed in the profile plot along with the scanned points. Options are available to control the presentation of the profile plots.

Tunnel profiles areas and volumes report

This stylesheet is designed to be used only with the File and Report Generator utility.

This stylesheet produces a report of the undercut and overcut areas on each tunnel profile as well as undercut and overcut volumes computed by average end areas. The stylesheet requires the selection of the appropriate TunnelXML file defining the tunnel design so that areas and volumes can be computed. It is also possible to optionally provide starting and ending stations for a station range over which the values are to be computed.

Tunnel profiles Word report with areas

This stylesheet is designed to be used only with the File and Report Generator utility.

This stylesheet produces a Microsoft Word XML format file (with a .doc file extension) that can be viewed in Microsoft Word. The Word file contains an initial cover page followed by a page per profile with a plot of the profile as well as a table with the computed area values and a table of the points scanned on the profile.

When you apply the stylesheet using the File and Report Generator utility, you can select the TunnelXML file that defines the tunnel alignment and design profiles used during the tunnel scanning operation. The design profile will be displayed in the profile plot along with the scanned points. Options are available to control the presentation of the profile plots.

Tunnel profiles DXF file

This stylesheet is designed to be used only with the File and Report Generator utility.

This stylesheet produces a DXF format file containing a set of tunnel profiles based on the points scanned in the job and the tunnel definition. When you apply the stylesheet using the File and Report Generator utility, you can select the TunnelXML file that defines the tunnel alignment and design profiles used during the tunnel scanning operation.The design profile will be displayed in the profile plot along with the scanned points. Options are available to control the presentation of the profiles in the DXF file.

Tunnel profile detail report

This report provides a list of the points scanned at each tunnel profile along with their Underbreak/Overbreak and station delta values. Any Underbreak/Overbreak or station delta values that exceed the specified tolerances are highlighted in the report.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Tunnel profile report

This stylesheet will create a summary report for each station scanned, listing the number of profile points and how many of those points were in or out of tolerance. It provides the number of overbreak and underbreak points and how many were outside the station tolerance. You can elect to use the overbreak, underbreak and station tolerances as specified when the scan was done, or you can enter your own tolerance values.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Tunnel profiles display (SVG)

This stylesheet is designed to be used only with the File and Report Generator utility.

This stylesheet creates an SVG (Scalable Vector Graphics) XML file of the tunnel cross-sections, which can be viewed in a web browser. The Prev and Next buttons allow you to step through the cross-sections, and on each cross-section you can 'hover' over the displayed points to see the overbreak/underbreak and delta station values for the points. The points are color‑coded to indicate whether they are within the specified tolerances. You can also specify the name of the tunnel, including the file path to the tunnel file, or just the file path itself, and the stylesheet will use the tunnel name referenced in the job to locate the definition file. If the tunnel definition file can be located, the design profile lines are displayed as well as the measured points.

Amberg tunnel profile report

A tunnel profile report for use in Amberg Tunnel office software.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Tunnel cross section points

This file is designed to provide a comma separated set of points that can be loaded into a suitable system for analysis. The tunnel delta points are output as Point name, 'east value', 'north value', 'elevation value'. The computed distance (as a set of outer chords summed together) left and right of the centerline is the 'east value', the station value is the 'north value' and the overbreak/underbreak value is output as the 'elevation value'. This is effectively like laying the measured cross-section points out in a line.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

LandXML to TunnelXML

The two stylesheets provided are designed to be used only with the File and Report Generator utility.

They are used to convert a LandXML version 1.0 file containing tunnel definition records to a TunnelXML file, that can then be used in Trimble Access. These tunnel definition records are stored as TunnelProfile elements in LandXML format files and are used by Novapoint and Leica. Note that these TunnelProfile records are not included in the LandXML v1.0 schema definition and so these files would not validate against the LandXML v1.0 schema. Once you have created a TunnelXML file using one of the stylesheets in the File and Report Generator utility, you can copy the TunnelXML file onto the controller running Trimble Access and use it for tunnel scanning. There is an instruction file included that covers the use of the two stylesheets provided. The Multi-surface stylesheet allows for cases where the elements for template arcs have arc mid point position recorded in the element rather than recording the true arc center position.

SierraSoft LandXML to TunnelXML

This stylesheet is only designed to be used only with the File and Report Generator utility.

It is used to convert a LandXML file containing tunnel profiles stored as standard LandXML CrossSectSurf elements to a TunnelXML file, that can then be used in Trimble Access. When run in the File and Report Generator utility, you can choose the tunnel profile surface name to be included in the TunnelXML file.

Once you have created a TunnelXML file using this stylesheet in the File and Report Generator utility, you can copy the TunnelXML file onto the controller running Trimble Access and use it for tunnel scanning.

Tunnel Bever control points

This file is designed to provide the scanned tunnel profile points in the Bever Control Profiler log format. This format provides the X,Y,Z coordinates of the profile points with the points named according to the profile they are on.

TunnelXML (TXL) to VMT XML

This stylesheet converts an RXL file to a DC file containing the road definition data.

TunnelXML definition report

This stylesheet creates a report using the data in the TXL file, that lists the stations along the tunnel (both geometric and regular stations) with identifiers for the geometric points and design elevations for each station. This report can be used to assist in the validation of tunnel designs prior to staking out.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Surpac STR file

This stylesheet creates a Surpac .str file which is the native format for the Gemcom Surpac Mining software widely used in Australia. The stylesheet starts a new Surpac string each time a new code is encountered.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Mine stakeout report

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Mine auto stakeout report

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Alignment report (CSV)

A report in CSV format which displays displacement information for the alignment. Displacement information is given for each station along the alignment, offsets perpendicular to the alignment, and vertical movement above or below the alignment.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Alignment Word report

A report in Word format that displays scatter plots and trend graphs showing displacement information for the alignment. Displacement information is given for each station along the alignment, offsets perpendicular to the alignment, and vertical movement above or below the alignment.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Epoch reference compare report (coordinates)

A report in HTML format which contains the point ID, coordinates, and time stamp for each monitoring point and round measurement. This streamlines transferring data to an office software for reporting.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Epoch reference compare report (CSV)

A report in CSV format which contains the point ID, coordinates, and time stamp for each monitoring point and round measurement. This streamlines transferring data to an office software for reporting and deliverable creation.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Epoch reference compare report

A report that shows the movement of every point in every epoch, compared with the first set of observations. Any displacements that are above the tolerances specified in the job are highlighted in red.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Point report

A report that shows the movement of one predefined point, compared with the first set of observations. Any displacements that are above the tolerances specified in the job are highlighted in red.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Word report

A report in Word format that displays a scatter plot and trend chart for each point, showing the displacements over time. The report includes a comprehensive displacement chart showing all monitoring points in one view, which is useful for determining trends or outliers in a group of monitoring points while in the field.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.

Land Seismic

These stylesheets create reports for points and staked points used with the Land Seismic app.

These stylesheets are installed to the Trimble Data / System Files folder on the controller with the software.

Power Line report

This stylesheet creates a report for the power line.

This stylesheet is installed to the Trimble Data / System Files folder on the controller with the software.